The BitLocker encryption key cannot be obtained from the Trusted Platform Module (TPM)… Unable to do a clean install on HP Spectre x360 (2017) with UEFI enabled.

Since there seemed to be limited answers out there I decided to blog about a system installation issue I ran into…

Ran into a few problems recently after deciding to upgrade the SSD in a new HP Spectre x360. The supplied drive was a 512GB, and was upgrading it to 1TB, as 512GB is a little on the low side for the work I do.

Having taken backups and replaced the old drive, I proceeded to install from a standard ISO pushed onto a USB.

The default settings (UEFI enabled) refused to see the standard ISO for Windows 10 Pro, so I had to switch it to legacy mode (which disables secure boot), within the BIOS. This allowed the USB to be detected and install to go smoothly.

Cut to install completed, and system running smoothly… for my work I must enable BitLocker and encrypt my drive… going through the options the verification check fails

Error - BitLocker could not be enabled.

The BitLocker encryption key cannot be obtained from the Trusted Platform Module (TPM).

I can force enable BitLocker but TPM will not function properly and I have to enter the decryption key every time I start the computer.

UEFI is still disabled.

”TPM.msc” (through start menu) and “get-tpm” (through an admin PowerShell) confirm that TPM is enabled but operating with reduced functionality and not ready for full use.

A quick check seems to indicate that TPM 1.2 is OK with legacy boot mode, but TPM 2.0 (as in my new system) requires UEFI to be enabled, along with secure boot for TPM to fully function.

Enabling UEFI obviously fails to recognise the drive, since it was installed with legacy mode which installs it with MBR (master boot record), as opposed to the UEFI requirement of GPT (GUID partition table).

Incidentally with TPM operating in a diminished mode, Hyper-V cannot use TPM and will fail on any encrypted VMs (also a requirement for me).

Checking the HP Support site; their only recommendation is to pay them for the HP install media, which will install their version of the OS along with all their utilities and bloatware… erm no thanks!

Some light research showed that I could create my own UEFI boot media using Rufus… Rufus is an open source stand alone EXE that you can run locally – full details can b found here – and can be downloaded from


However, having already completed the installation, wanted to avoid this if I could.

… what to do …

Well, Microsoft to the rescue. The latest version of Windows 10 now includes a new tool, which allows a MBR install to be converted to GPT with one line from Command Prompt… the tool has additional abilities also.

The following command run from an elevated (administrator) command prompt will allow you to convert the current disk to GPT.

C:\WINDOWS\system32\mbr2gpt.exe /convert /allowFullOS


MBR2GPT.EXE converts a disk from the Master Boot Record (MBR) to the GUID Partition Table (GPT) partition style without modifying or deleting data on the disk. The tool is designed to be run from a Windows Preinstallation Environment (Windows PE) command prompt, but can also be run from the full Windows 10 operating system (OS) by using the /allowFullOS option.

After conversion is completed (for me it only took a few seconds), you need to reboot and change your BIOS settings to re-enable/enable UEFI along with secure boot.

Full details of MBR2GPT may be found here –

You should then find that TPM is functional again…

… however if still having issues… you should clear and prepare TPM by i) opening up TPM.msc, ii) “Clear TPM”, iii) reboot, iv) open TPM.msc again and then v) choose “Prepare the TPM”.


After jumping through a few hoops I was able to successfully encrypt my drive and then enable TPM encryption within Hyper-V.

BitLocker Enabled

BitLocker Enabled – note: you can open TPM.msc from start menu (by typing TPM.msc) or from BitLocker window (“TPM Administrator”).